International Journal of Engineering Research in Mechanical and Civil Engineering (IJERMCE)

Monthly Journal for Mechanical and Civil Engineering

Volume3,February 2018,

Topic : Analysis of Residual Stress and Distortion for the Manufacturing of Axle Drive Shaft

Authors:Rajeshdan Gadhavi || Nirav Doshi

Abstract:This paper analyses the effect of residual stress in the distortion of the axle drive shaft. Residual stress is the stresses that remain in a solid material after the original cause of the stress has been removed. An axle drive shaft of 20MnCr5 material is been analyzed. Research is carried out on two axle drive shaft. In one shaft, after the last manufacturing step was sent through residual stress relief process by shot peening process. And both shafts after going through heat treatment process showed variation in distortion. The shaft with stress relief treatment showed less amount of distortion compared to the other shaft. Therefore a stress relief shot peening process is recommended for reducing the distortion in axle drive shaft..

Keywords: Residual stress, axle drive shaft, heat treatment

Download Paper


DOI: 01.1617/vol5/iss2/pid82509


Related Articles

RFID Technology in Construction Project Management – A Review

Authors: Rounak Bhushan Singh || Sumeet Sagar,Animesh Sinha,Muneesh Methwani

Doi : 01.1617/vol4/iss03/pid49278

Volume2 ,March 2018.

RFID Technology in Construction Project Management – A Review

Authors: S.Pachaiappan || Dr.S.Palanivel

Doi : 01.1617/vol4/iss03/pid49278

Volume2 ,March 2018.

Experimental Study of Steel Fibers Reinforced Concrete over Conventional Concrete

Authors: Varsha Harne || Suyog U. Dhote

Doi : 01.1617/vol4/iss03/pid83154

Volume2 ,March 2018.

Experimental Investigations of Rubber Seed Oil Methyl Ester-Diesel and Butanol-Diesel Blend by Using Diesel Engine

Authors: Vishal V. Patil || Utkarsh Shidhganesh,Somesh Shinde,Mahesh Gurav,Swapnil Ulagadde

Doi : 01.1617/vol4/iss2/pid72430

Volume2 ,February 2018.

Study of Land Acquisition Issues causing delay of NHAI Projects

Authors: Rounak Bhushan Singh || SumeetSagar, Animesh Sinha

Doi : 01.1617/vol4/iss4/pid73465

Volume2 ,April 2018.

Study on Strength and Durability Properties of Bacteria Concrete

Authors: Phani Kumar. V || V. Sainath,Ashok Varma

Doi : 01.1617/vol4/iss3/pid03875

Volume2 ,March 2018.

Influence of Masonary Infill on The Behaviour of RC Frames

Authors: R.Vigneshwaran || Dr.K.Pandurangan

Doi : 01.1617/vol4/iss3/pid01729

Volume2 ,March 2018.

Design of Smart Rolling Shutters for Low Cost Operations

Authors: Kushali Sindhia || Madhumitha Prakash,Dr. S. V. Satish

Doi : 01.1617/vol4/iss3/pid49615

Volume2 ,March 2018.

An Experimental Investigation on Behavior of High Volume Alkali Activated Flyash Concrete

Authors: K.Sasidhar || S. Aruna Jyothy,Dr. B. Damodhara Reddy

Doi : 01.1617/vol4/iss3/pid64813

Volume2 ,March 2018.



Editor-in-chief

Editor Image

Editor-in-Chief
Meinhard Taher Schobeiri
Professor,
Texas A & M University, USA.

View more


IMPACT FACTOR: 3.8

ISSN(Online): 2456-1290

Google Scholar Profile

Thomson Reuters ID : q-6288-2016.
ORCiD Research ID : 0000-0001-9540-6799

All Issues

ACCEPTANCE RATIO

ACCEPTANCE RATIO: 25%
ARTICLES PUBLISHED:00007
PAPER RECEIVED:000028
Journal Code : IJERMCE
Electronic ISSN : 2456-1290
Impact Factor : 3.8
Frequency : monthly
Contact : info@ijermce.com

IFERP Other Journals


Subscribe

           Email:

SOCIAL MEDIA