Open Access Journal

ISSN : 2456-1290 (Online)

International Journal of Engineering Research in Computer Science and Engineering (IJERCSE)

Monthly Journal for Computer Science and Engineering

Open Access Journal

International Journal of Engineering Research in Mechanical and Civil Engineering (IJERMCE)

Monthly Journal for Mechanical and Civil Engineering

ISSN : 2456-1290 (Online)

Call For Paper : Vol 11, Issue 08, August 2024

Call for Paper

Vol 11, Issue 08, August 2024

Indexing

A Review on the Mufflers used in Automotive Vehicles

Author : Ujjal Kalita 1 K.Anjaneyulu 2 Sandip Dey 3 Manpreet Singh 4

PDF

Date of Publication :31st December 2021

Abstract: In the 21st century, the automotive industry is booming. A major problem with internal combustion engines (I.C.) is that they are an important cause of noise pollution. It is for this reason that mufflers are used to reduce the noise produced. Although mufflers are not designed to perform any of the main output functions, they are included within the I.C. engines. It is designed as a sound protection device that reduces engine pressure. But mufflers need structure and geometry, if you think the physics behind it are very confusing. The muffler design developed into a repetitive process with trial and error. Recent research in this area has made it possible to do so through analytical and experimental methods. Modern engines are required to have more engine electricity and also are required to fulfil the stern pollutants standards. In a car, the exhaust muffler plays an essential position in decreasing the sound of the car, in addition to the experience itself. So as to preserve a preferred noise and at ease ride, the modes of a muffler need to be analyzed. In this study a literature review was performed on all the different aspects that could be taken while designing an exhaust muffler. Here dynamic modal analyses had been purchased using CAE evaluation to determine the mode size, strain and deformation of the exhaust muffler

Reference :

    1.  M.L. Munjal, Acoustics of ducts and mufflers with application to exhaust and ventilation system design, John Wiley & Sons, 1987
    2. M.L. Munjal, Plane wave analysis of side inlet/outlet chamber mufflers with mean flow, Appl. Acoustics, 52, pp.165–175, 1997
    3. M.B. Xu, A. Selamet, I.J. Lee, N.T. Huff, Sound attenuation in dissipative expansion chambers, J. Sound Vib. Vol. 272,pp. 1125–1133, 2004
    4. T W Le Roy, Muffler characterization with implementation of the finite element method and experimental techniques Michigan Technological University, 2011
    5.  A. Elsayed, C. Bastien, H. Medina, S. Jones, H. Kassem, Enhancing Noise Attenuation in Exhaust Mufflers on Response to Baffle Configuration, Int. J. Eng. Manuf.vol 7 pp. 12–25, 2017
    6. U. Kalita, M. Singh, Design and CFD analysis of flow through a reactive muffler of four cylinder diesel engine, recent trends in Engg. Design, Lecture Notes of Mechanical Engg,pp. 211-223, 2021
    7. P.O.A.L. Davies, R.J. Alfredson, Performance of Exhaust Silencer, J. Sound Vib. Vol. 15, pp.175–196, 1971
    8.  D. Potente, General design principles for an automotive muffler, Annu. Conf. Aust. Acoust. Soc. 2005, Acoust. Chang. Environ., pp. 121–126, 2005
    9.  O.Z. Mehdizadeh, M. Paraschivoiu, A three-dimensional finite element approach for predicting the transmission loss in mufflers and silencers with no mean flow, vol 66, pp. 902–918, 2005
    10. M.L. Munjal, Recent advances in muffler acoustics, Int. J. Acoust. Vib, vol. 18, pp.71–85, 2013
    11. V. Sherekar, P.R. Dhamangaonkar, Design principles for an automotive muffler Int. J. Appl. Eng. Res, Vol. 9 pp. 483– 489,2014
    12. S. Balamurugan, N. Jeyaprakash, K. Manikandan, Design and Fabrication of Muffler for Four Stroke Diesel Engine, Int. J. Sci. Eng. Technol. Vol. 4, pp. 136–140, 2015
    13. A. Ahmed, Design and construction of absorption type muffler and compare it with engine ’ s existing muffler prepared by, (n.d.)
    14. ] P. Saripalli, CFD Analysis on Flow Through a Resistance Muffler of LCV Diesel Engine, Int. J. Sci. Technol. Soc. Vol. 3, 2015
    15. P. Srinivas, V.R. Mamilla, G. Lakshmi, N. Rao, M. Ahmed, Design and Analysis of an Automobile Exhaust Muffler, Ind. Syst. Eng. Vol 1, pp.10–15, 2016
    16. G. Gnanendhar Reddy, N. Prakash, Design and fabrication of reactive muffler, Int. J. Chem. Sci. Vol.14, pp.1069–1076, 2016
    17. V.D. Prajapati, Design and Analysis of Automotive Muffler, Vol 5, pp. 384–389, 2016
    18. M.R. R, Components That Influence Airflow Out of the Engine Are As Three-Way,Int. J. Automob. Eng. Res. Dev.Vol. 2, pp. 11–21, 2012
    19. P.V. Lokhande, Design Analysis of Exhaust Muffler With VOC Emission Filter,Int. Res. J. Eng. Technol. pp. 699–709, 2012
    20.  20. J.H. Chaudhri, P.B.S. Patel, P.S.A. Shah, Muffler Design for Automotive Exhaust Noise Attenuation - A Review, Vol 4, pp. 220–223, 2014
    21.  U. Kalita, M. Singh, Optimization of a reactive muffler used in four-cylinder petrol engine into hybrid muffler by using CFD analysis, Materials Proceeding Today, (2021) [22] N. Patil, S. Chaudhary, CFD analysis of exhaust backpressure for four-stroke ciengine, Vol.3,pp. 247–252, 2018.

Recent Article